Shravan Kumar, A Praveena, S Jayaprakash


The problem that has confronted the producer is the manager of the gadget enters parameters to collect a tremendous welded joint with the preferred weld splendid. Traditionally, it is been important to have a have a look at the weld enter parameters for the welded product to gather a welded joint with the popular terrific. To gain this requires a time-ingesting trial and errors improvement approach. Then welds are examined whether or not or no longer or no longer have they met the requirement or not. Finally, the weld parameters may be decided on to supply a welded joint that cautiously meets the joint capabilities. Also, what isn't completed or often considered is an optimized welding parameters combination, for the purpose that welds can frequently be common with very specific parameters. In distinctive phrases, there can be regularly at in addition ideal welding input parameters mixture, which may be used. In this thesis, they've got an impact on of welding parameters like welding contemporary-day, welding voltage, welding tempo on last tensile power of AISI 1050 slight metallic material for the duration of welding. A plan of experiments primarily based mostly on the Taguchi method has been used. An Orthogonal array, a signal to noise (S/N) ratio and assessment of variance (ANOVA) are employed to have a have a examine the welding developments of material & optimize the welding parameters. The save you quit end result computed is inside the form of contribution from each parameter, through which the greatest parameters are identified for optimum tensile strength. From this check, it's far decided that welding present day and welding pace are most vital parameters which have an effect at the tensile energy of the welded joint.


S.Utkarsh, P. Neel, Mayank T Mahajan, P.Jignesh, R. B.Prajapati:- have provided “Experimental Investigation of MIG Welding for ST-37 Using Design of Experiment” (International Journal of Scientific and Research Publications, Volume 4, Issue 5, May 2014 1 ISSN 2250-315)

Parametric optimization of MIG welding the usage of Taguchi layout method By S.V. Sapakal, M.T. Telsang International Journal of Advanced Engineering Research and Studies E-ISSN2249–8974.

Optimization of MIG welding approach parameters to are waiting for most yield strength in AISI 1040 with the useful resource of the use of Ajit Hooda, Ashwani Dhingra and Satpal Sharma ISSN 2278 – 0149 Vol. 1, No. Three, October 2012.

A Review on Optimization of MIG Welding Parameters the use of Taguchi’s DOE Method via way of Satyaduttsinh P. Chavda, Jayesh V.Desai, Tushar M.Patel Volume4, Issue-1, February-2014, ISSN No.: 2250-0758 International Journal of Engineering and Management Research.

Metal Inert Gas (Mig) Welding Parameters Optimization By B. Mishra1, R.R. Pandaand D. K. Mohanta International Journal of Multidisciplinary and Current ResearchISSN: 2321-3124.

Optimization of MIG welding for improves power of welding joints International Journal of Advanced Engineering Research and Studies E-ISSN2249–8974 (Int. J. Adv. Engg. Res. Studies / II/ IV/July-Sept., 2013/14-sixteen).

Genichi Taguchi (1986), “Introduction to Quality Engineering: Designing Quality into Products and Processes”, Asian Productivity Organization.

M. S. Phadke (1989), “Quality Engineering Using Robust Design”, Prentice Hall, Englewood Cliffs, New Jersey.

D. Dubois, and H. Prade (1980), “Fuzzy Sets and Systems: Theory and Applications”, Academic Press, New York.

Full Text: PDF


  • There are currently no refbacks.

Copyright © 2012 - 2021, All rights reserved.|

Creative Commons License
International Journal of Innovative Technology and Research is licensed under a Creative Commons Attribution 3.0 Unported License.Based on a work at IJITR , Permissions beyond the scope of this license may be available at